Thin under tile floor heating installations have traditionally involved complicated installation procedures, and the thin heating cables supplied on a roll also require careful planning to ensure there are no hot or cold spots.
The unique Thin Cable Mat design removes the risk of uneven heat spots and simplifies installation as the heating cable is uniformly fixed to the underside of a nylon mat supplied with strips of adhesive tape for direct stick to the prepared floor.
The ease of installation also makes them an ideal Trade Kit without requirements or experience for planning floor heating layouts.
Also, the thin floor heating systems construction and installation methodology does not require any special tools and is quickly stuck to a clean subfloor using the attached adhesive tape strips.
| Application | Direct & background heating for installation over concrete or F/C sheet floors. The mat is embedded in the tiles adhesive or a thinset beneath most hard floor finishes including tile, floating and timber floors. |
| Mat Construction | Comprises of a flexible fiberglass mesh with the looped heating element uniformly affixed to it. Tape strips or adhesive backing on the bottom side of the mat heater allows for fixing the mat heater to the floor. The heating element terminates to a 3m length cold lead at both the start and end of the mat heater. |
| Element Construction | Thin 2.2mm self regulating single heating conductor with a primary Fluoropolymer (Teflon) insulation, then layered with a steel earth braid and a final outer PVC insulation sheath. |
| Voltage | 240V AC |
| Output Power | From 150 to 200W/m² |
| Control | Analog or Digital Programmable room or floor sensing (or a combination of both) thermostat |
| Safety | Connection to electrical supply must conform to AS/NZS 3000 wiring regulations. The heating cable is tested to be IPX7 & IEC60335 compliant, and is safe for use in wet area Zones 1, 2, 3 as per AS/NZS 3000 wiring regulations |
| Warranty | 20 Years (as of 1 April 2020) |
Thin Cable Mat 20 Range – for bathrooms
| Product Code | Mat Size (mtr) | Floor Area (m²) | Watt @ 240V | Amp @ 240V |
| CM200-20 | .5 x 2 | 1 | 200 | 0.9 |
| CM300-20 | .5 x 3 | 1.5 | 300 | 1.3 |
| CM400-20 | .5 x 4 | 2 | 400 | 1.7 |
| CM500-20 | .5 x 5 | 2.5 | 500 | 2.2 |
| CM600-20 | .5 x 6 | 3 | 600 | 2.6 |
| CM700-20 | .5 x 7 | 3.5 | 700 | 3.0 |
| CM800-20 | .5 x 8 | 4 | 800 | 3.5 |
| CM900-20 | .5 x 9 | 4.5 | 900 | 3.9 |
| CM1000-20 | .5 x 10 | 5 | 1000 | 4.3 |
| CM1200-20 | .5 x 12 | 6 | 1200 | 5.2 |
| CM1400-20 | .5 x 14 | 7 | 1400 | 6.1 |
Cable Mat 15 Range – for living areas
| Product Code | Mat Size (mtr) | Floor Area (m²) | Watt @ 240V | Amp @ 240V |
| CM750-15 | .5 x 10 | 5 | 750 | 3.3 |
| CM900-15 | .5 x 12 | 6 | 900 | 3.9 |
| CM1200-15 | .5 x 16 | 8 | 1200 | 5.2 |
| CM1500-15 | .5 x 20 | 10 | 1500 | 6.5 |
| CM1800-15 | .5 x 24 | 12 | 1800 | 7.8 |
| CM2250-15 | .5 x 30 | 15 | 2250 | 9.8 |
Installation of Thin Cable Mat is a simple process offering reduced installation time. After the subfloor has been prepared (cleaned and in some cases primed with a bonding agent), Thin Cable Mat is rolled out and stuck to the floor using the attached adhesive tape strips. The flooring can be immediately installed after the element fault monitor is connected to the cold tail leads.